Premium o ring manufacturer: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Read more info at scraper seals.

Every other leak path within the mechanical seal is blocked with the use off a gasket, o-ring, wedge (Rubber, PTFE or Flexible Graphite). The other key aspect of a mechanical pump seal is how to maintain the seal. Springs (single or multiple), a metal bellows or just compressed elastomers are used to provide the needed energy to keep pressing the seal faces together. The load the seal faces receive are engineered into the design of the seal. The choice of what is the best depends on the temperature, and nature of what is being sealed (viscosity, abrasiveness, weight (is it a slurry?)). Cartridge Seals are pre-assembled package of mechanical seal components making installation much easier with fewer points for potential mechanical pump seal installation errors to occur. Mechanical seals occasionally require a seal pot to provide a buffer fluid for your double cartridge seals. Seal pots can not only provide a lubricating buffer, but they can also heat or cool the barrier fluid they contain.

Due to the volume and weight limitations of the system, it is impossible to install an ideal filtration and cooling system. High temperature, high pressure, and high speed cause the hydraulic oil to deteriorate easily, and the mechanical parts are also prone to erosion and stains. There are many stains and impurities in hydraulic oil, but it cannot be thoroughly filtered, which is the aspect of endogenous stains. All kinds of dust in the working environment may be very large, and it will inevitably enter the hydraulic system in multiple ways, causing oil pollution, which is an external stain. Therefore, the sealing system is required to be resistant to stains.

It can be used as a guide ring for the piston rod to support and guide the piston rod. It has excellent vibration damping performance and is simple and safe to install. It is made of metal and plastic materials. It can prevent work stagnation and violent vibration. The embossed structure facilitates the formation of lubricating micro-pits and improves lubrication. At the same time, the seal prevents the intrusion of tiny foreign objects and protects the sealing system.

Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.

DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.

Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.

Supplied in rolls or open loops. The open ring can be directly installed and used, but it must be cut when the roll is used, and the cutting length must be calculated in advance: there can only be one opening, the opening form is an oblique 45° opening, and the opening distance is about 3-15mm, or the diameter of the guide ring 3-5% of . Under normal circumstances, the openings are oblique openings. Straight openings or zigzag openings are rare and have specific uses and purposes. There are two purposes for the opening. The first is to facilitate installation. If it is not opened, it is an integral ring, which is difficult to install or impossible to install, so it must be opened. Secondly, the opening and a certain opening distance are reserved to facilitate the automatic coordination of volume changes. Otherwise, the movement may be stuck or the moving parts may be pulled due to the excessive expansion of the guide belt under certain conditions. Coiled ones are relatively cheap, and the same coil can be used to make guide rings of different sizes. Read more information on https://www.dmsseals.com/.

DMS Seals is a professional mechanical seals manufacturer and oil seal supplier for hydraulic seals, O-Rings, spring energized seals, oil seals, mechanical seal and so on. Hydraulic seals including step seals, glyd rings, guide strips, wiper seals, rod seals, piston seals, rotary seals, wear rings. We can provide the hydraulic seals with bronze filled PTFE, carbon filled PTFE, graphite filled PTFE, MoS2 filled PTFE, glass filled PTFE, virgin PTFE. About O-Rings, we can supply NBR, FKM, silicone, EPDM, HNBR, ACM, FFKM material.