Cutting discs shop in the United Kingdom 2023? If value for money is a priority to you, take a look at this drill from Evolution. It is a solid and durable drill that will get the job done for the professional steelworker as well as the weekend handyman. This drill has a 6-inch stroke length and comes with a 0.5-inch chuck and key. The drilling range has a diameter from 7/16? to 1-1/8? and cutting depth of 2 inches unless you change out the chuck to something else. You can place the feeding handle on either side of the drill, depending on what is comfortable to you. The heavy-duty magnet makes it easy to do overhead or horizontal drilling. An integrated cooling system will keep your magnetic drill press from overheating. There are some drawbacks to this drill. It can only turn at the speed of 570 RPM. This works great for when you are drilling steel or aluminum, but this speed is too high for drilling titanium or stainless steel. This drill may also be more primitive than conventional high-end magnetic drill presses. Discover additional information here Welding Supplies Direct stock a wide range of mag drills from industry leading manufacturers such as JEI Solutions, Alfra, Rix Tools, FEIN & Holemaker Technology. Our flagship mag drill partner, JEI Solutions, have a range that is suitable for every drilling / broaching application; be it low profile applications, on-site cutting for structural jobs or simple at home, DIY drilling. The HMT VersaDrive V35 is a British made 35MM mag drill that is available in both 110V & 230V input voltages. It has a 35MM maximum cut capacity with a 110MM maximum cutter length and is perfect for all drilling applications, especially structural steelworks. Find more information here mag drills.

Important Industrial Gas Cylinder Safety Guidelines to Keep in Mind: Acetylene and oxygen are two industrial gases widely used across various industries. The cylinders accommodating these gases are designed with user’s safety in mind. However, that is not enough to ensure optimum safety in an industrial facility. The following factors will help ensure the same: Understand the Cylinder Properly: A personnel should be familiar with the potential risks and hazards associated with compressed gases while handling them. It is important to understand the properties of the gas filled within such as toxicity, flammability limits, and toxicity – Threshold Limit Value (TLV). Also, it is important to understand the hazards posed by gas at low temperature, high pressure or due to the physical state of the gas – non-liquefied or liquefied, etc. A personnel should read the contents of the label on the cylinder. If the label is missing or not easily readable, then the cylinder should not be used. In addition to improving a personnel’s understanding on oxygen cylinder safety or acetylene cylinder safety, he should be administered a proper plant safety training.

Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber.

The Forney Easy Weld 140 FC-i is a great MIG welder for home use. The “FC-i” in the name means “Flux Core inverter.” Inverter technology is lighter than traditional transformers used in most welders, meaning this welder delivers 140 amps even though it only weighs 19 pounds. The one thing this welder doesn’t offer is true MIG capability. Flux core wire doesn’t deliver the same clean, indestructible level of welding as a gas-shielded arc. It provides shielding by evaporating flux. For the average home welder, the difference is minor. However, if you need to weld aluminum or stainless steel, flux core wire isn’t up to it and you’ll need to find a MIG-capable machine. The 140-amp rating is about as hot as you can get without stepping up to 220 volts. That’s enough to weld 1/4-inch steel. The duty rating on this machine is 30 percent at 90 amps, pretty astounding on a machine in this price range. There’s probably not a MIG welder in this class that has more satisfied customers, a big reason it’s the Weld Guru Weekend Warrior selection for Best MIG. If you don’t have a lot to spend, then I would recommend taking a look at our cheap MIG welders for under $500 guide.

Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.

How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.

US tool brand DeWalt are known for making the best angle grinders, and the DCG405N is a step above the competition. Cutting the cord once and for all, this is a powerful grinder that makes use of DeWalt’s excellent XR battery system. This Dewalt angle grinder is not just a powerful cordless grinder though. The grip shape is supremely comfortable, and the whole unit weighs just 1 kg without the battery installed. You can lock-off the power switch when you need to get the grinder into awkward spots as well. This brushless angle grinder also features a host of clever safety features. I like the no-volt release to prevent accidental start-ups when a new battery is installed. The electronic brake and clutch are essential for safe operation too. The 18V brushless motor is ideal for battery use. It can make 69 cuts in ½” steel rebar when used with a 5.0 Ah battery. It doesn’t come with any batteries or one of DeWalt’s excellent TSTAK cases though, which is the case with bare power tools.

Some advices about welding equipment, MIG and TIG welders, plasma cutters. MIG Welders are extremely popular because they tend to cost less than TIG or Stick welders with comparable power and features, are extremely easy to learn, and can tackle a wide variety of projects. Since the filler metal is fed through the MIG welding torch, welders can use both hands to hold the torch steady rather than using one hand to add filler metal, as in TIG welding. The wire feeder also makes MIG welding up to four times faster. The MIG welding process uses an inert gas to shield the weld and to keep it free from impurities. This makes MIG welding very neat and easy to clean up since there isn’t anything to chip away, which is typical for Stick welding. MIG welding can be used on a wide variety of materials such as aluminum and is also frequently used for automotive work. However, MIG also requires the purchase of shielding gas and generally requires materials that cost more when compared to other methods.

Successfully Prevents Toxic Gas and Can Replace Any Ventilation Fan. Maxx Air HVHF is more about preventing toxins from traveling around your home or workplace than it is about regulating temperature. This is the perfect fume extractor if you don’t want ventilation fans installed around your property. You can use it basically for any sort of welding and soldering job. As it produces massive 2000 CFM airflow, you don’t have to worry about its performance! KNOKOO is famous for producing lightweight fume extractors within an affordable price range. The FES 150 is a worthy inclusion in their list of products. This portable weld fume extractor absorbs smoke and purifies the air as well with its 3-layered filter.

Our vision and our distinct set of values drive the success and spirit of our organization. At ESAB, under Colfax leadership, we live our values. As a premiere U.S. welding equipment manufacturer, our vision and values help us to make strategic decisions, allocate resources, and focus our choices every day, domestically and internationally. ESAB offers a world of products and solutions for virtually every welding and cutting process and application. We serve industries that serve the world. The Best Team Wins – Team-oriented, involved associates are our most valuable resource, and we are passionate about attracting, developing, and retaining the best talent. Living this value is done in three primary ways: 1. Building the right team – having the right people to do the job; 2. Creating the right environment – making sure that leaders create an environment where all associates can contribute, and 3. Getting the win – when you have the right people and right environment – it makes getting the win a lot easier!

These welding tables are manufactured to the highest standards in Poland, Europe by GPPH. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. The hole system that these welding benches offer make precise construction a much quicker process when used in conjunction with the optional tool sets. Batch work processing times can be cut in half when you eliminate the measure and exact angle arrangement of individual parts – this makes producing the same item simple and fast.

United Kingdom market pick: LONGEVITY Inc is a company that has been around since only 2001. Like LOTOS Technology, it still produces a fine enough quality welder that it has earned its spot on this list. Besides the gas cylinder, this welder comes with everything you need to get started and is simple to set up. With all this, along with its solid performance, this machine is marked at a fair price of under $400. Though it is manufactured in China, the LONGEVITY Migweld is still a quality welder. It is most well-adapted to light use. Compared to Miller and Hobart’s machines, the price is somewhat better without sacrificing much quality. It welds from 24 gauge to ¼ inches of steel. Flux core is available for this welder. The LONGEVITY can run at ten different voltage settings. As an added bonus, it has thermal overload protection like the LOTOS welder.

The Lincoln EasyMIG 180 is a well-built welder that’s reliable and will serve a range of light fabrication and workshop projects. Its power input is 230V but it doesn’t have the power of the Hobart 190. This is a great entry level 230V welder that will give you quality welds. It won’t tackle thicker metal but this will do the job for most hobby welders. It’s a great choice for a hobbyist if you have a convenient 230V power outlet.

Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. Find extra details on https://www.weldingsuppliesdirect.co.uk/.

Out of a huge product range of the Dirty Pro Tools, we have found a top-grade MIG welder that turned out to be so good that we have decided to add it to this shortlist. It is the tool for welding metalware of medium thickness with the output range from 50? to 60?, best for sheets up to 2 mm thick. In addition, a pretty powerful converter of this welder allows working for about 6 minutes at 50?. So, you’ll be able to weld thin pieces for a good while, and the fan will provide a decent cooling of the tool. However, when the MIG welder overheats, the red light will flash telling you to stop welding and make a pause. By the way, you can pick either of 4 available amperage settings and adjust the wire feeding speed for reliable and straight welds. We were pleased by the package that includes a face shield, a clipping hammer, a brush and a spool of welding wire, so you can start welding right after unpacking the unit. So, this Dirty Pro Tools welder is one of the most affordable models for people seeking a mid-power machine to weld fine metal sheets.